GE-F128 Series Outdoor C&I Battery Cabinet · 96.5–128.6 kWh

Highlights

• Three capacities, one cabinet. Six, seven or eight 16.08 kWh LiFePO4 packs (314 Ah) give 96.46, 112.53 or 128.61 kWh at 307.2–409.6 V nominal. Under Deye’s test conditions (100% DoD, 0.5P, 25 °C) all of it is usable.
• The inverter mounts on the cabinet. The cabinet’s side wall has a preset bracket position for the hybrid inverter, so the inverter needs no wall mounting or drilling. Each cabinet takes one GE-F128-AP accessory kit, which holds the DC cables, communication cable, bracket and cable cover.
• Six-layer safety design. Deye lists electrical isolation, fire detection, active exhaust, explosion venting, fire suppression and thermal isolation. Inside the cabinet are heat, smoke and CO detectors and an aerosol fire-suppression unit. Outside are a water fire-fighting inlet and an emergency power-off button on the front, and a deflagration vent on the roof.
• Smart air cooling. A built-in air conditioner sends cooled air through ducts to the battery packs and power components in a closed loop. The cabinet operates from −30 to 55 °C, derated above 45 °C. It is rated IP55, with C4-M anti-corrosion as standard (C5 on request).
• Long-life LFP. Deye’s AU brochure rates the cabinet at ≥8000 cycles (25 °C ± 2 °C, 0.5P, 70% EOL).
• Scales both ways. Up to 10 cabinets run in DC parallel for capacity (1.28 MWh), or up to 10 cabinet-and-inverter units in AC parallel, on- or off-grid (0.6 MW). Cabinets can stand back to back or side by side.

Choosing the model and inverter

Model	Packs	Energy	Nominal voltage	Rated DC power	Hybrid builds in Deye’s AU documents
GE-F96-BC-2-A2	6	96.46 kWh	307.2 V	48 kW	SUN-29.9K-SG01HP3 (3-hour system)
GE-F112-BC-2-A2	7	112.53 kWh	358.4 V	56 kW	SUN-50K-SG02HP3-AU-BM4-P (2-hour system), marked “coming soon”
GE-F128-BC-2-A3	8	128.61 kWh	409.6 V	64 kW	SUN-29.9–50K-SG01HP3 · SUN-60K-SG02HP3 (2-hour) · SUN-40K-SG01HP3 (3-hour) · SUN-29.9K-SG01HP3 (4-hour)

Deye’s AU configuration list (V1.0, 2026-09-10) has one GE-F128 build: one GE-F128-BC-2-A3 cabinet and one GE-F128-AP-A kit with a SUN-29.9–50K-SG01HP3-AU-BM3/BM4 hybrid. Deye’s AU brochures (2026-09-04) add the SUN-60K-SG02HP3-AU-EM6 for a two-hour system; see the SUN-60–80K-SG02HP3 page. The 70–80 kW SG02HP3 models are not listed for this cabinet.

The GE-F96 and GE-F112 are not in the AU configuration list. Deye’s AU brochures pair the GE-F96 with the SUN-29.9K-SG01HP3-AU-BM3. They pair the GE-F112 with the SUN-50K-SG02HP3-AU-BM4-P, an inverter they mark as coming soon and which does not appear in Deye’s AU configuration list. Confirm the inverter for either model with Suncloud.

For 176.8–257.2 kWh in one cabinet, see the GE-F240/F256 Series.

Accessory kits (one per cabinet)

Each cabinet takes one of the two kits.

• GE-F128-AP-A is for inverters with a single or dual battery port up to 100 A, and it is the kit in Deye’s AU SUN-29.9–50K-SG01HP3 build. Deye’s manual (§4.2) also lists it for the 60 kW SG02HP3-EM6 (and the 30/40 kW SG02HP3). The SUN-60K-SG02HP3-AU-EM6 in the two-hour build has two 80 A battery inputs, which is within AP-A’s 100 A limit per port. It contains 2 positive and 2 negative 3AWG DC cables (3000 mm), a communication cable (3000 mm), the inverter mounting bracket and a cable cover.
• GE-F128-AP-B is for inverters with a single battery port up to 160 A. It contains 1AWG positive and negative DC cables (3000 mm), a communication cable (3000 mm), the bracket and a cable cover. Deye’s EU manual lists it for its 50 kW SG02HP3-BM4-P inverter only, and the AU version of that inverter is marked coming soon.

Site and installation notes

• The cabinet needs a three-phase auxiliary supply (L1/L2/L3/N/PE) of up to 2.6 kW per cabinet. The auxiliary cable is not supplied (manual §5.3.5).
• The manual (§6.2) makes black start available when two conditions are met: the ambient temperature is between −10 and 50 °C, and the cabinet’s auxiliary supply is fed from the LOAD port of the designated hybrid inverter. If the site needs black start, plan the auxiliary supply that way.
• Leave 100 mm between cabinets and to walls, and 1500 mm clear at the front (manual §4.1.1).
• The cabinet is floor-mounted on a purpose-designed foundation of concrete or another non-combustible surface (manual §4.1.2), and weighs up to 1690 kg.
• The manual’s siting distances are generic. Confirm the Australian siting and fire requirements for each project.

Model naming

This page follows Deye’s AU part-number list (V1.0, 2026-09-10). It names the six- and seven-pack models GE-F96-BC-2-A2 and GE-F112-BC-2-A2, and the eight-pack model GE-F128-BC-2-A3. Deye’s AU brochures and the user manual print all three with the -A3 suffix. The part-number list describes the GE-F96 and GE-F112 as reduced-pack versions of the GE-F128. Confirm the suffix when ordering.

Figures are from Deye’s ORION E GE-F128 Series Outdoor Battery Cabinet brochure (AU, V1.0, 2026-09-04), the ORION E GE-F128/F240/F256 + hybrid inverter + PCS 100–125 kW brochure (AU, V1.0, 2026-09-04), the GE-F128 Series user manual (EU edition, EN, V03, Issue A03, 2026-08) and Deye’s AU part-number and configuration list (V1.0, 2026-09-10). The manual is Deye’s EU edition, so follow Australian standards and local requirements for siting and wiring. The cycle life is the figure and test conditions printed in Deye’s AU GE-F128 Series brochure. Confirm the model suffix, accessory kit, inverter pairing and warranty terms with Suncloud before quoting or ordering.